Abstract：
:Cellulose acetate phthalate and Pluronic F-127 combined together (70:30 wt:wt) create a rigid, surface-eroding association polymer. To impart flexibility into the polymer system and allow for a drug delivery film that can contour to varying wound shapes, plasticizers were added. Triethyl citrate or tributyl citrate was combined with cellulose acetate phthalate and Pluronic F-127 at 0, 10, or 20 wt%. Mechanical analysis was performed on the films as they were prepared and following a 2-h incubation in phosphate-buffered saline. Tensile tests showed that higher plasticizer content increased the % elongation but decreased the elastic modulus and ultimate tensile strength. The effect triethyl citrate had on the % elongation was twice as much than that of tributyl citrate. After incubation, % elongation, elastic modulus, and ultimate tensile strength all increased because plasticizer leached out of the films. Microcomputed tomography and scanning electron microscopy were performed on the samples both before and after incubation to determine how erosion and leaching of plasticizer affected the interior and exterior structure of the films. Porosity increased as plasticizer content increased; however, plasticizer content did not have a significant effect on the rate of erosion. The mechanical properties of cellulose acetate phthalate-Pluronic films can be adjusted by the type and amount of plasticizer added to the system and therefore can be tailored for different drug delivery applications.
journal_name
J Biomater Appljournal_title
Journal of biomaterials applicationsauthors
Rabek CL,Van Stelle R,Dziubla TD,Puleo DAdoi
10.1177/0885328213480979subject
Has Abstractpub_date
2014-01-01 00:00:00pages
779-89issue
5eissn
0885-3282issn
1530-8022pii
0885328213480979journal_volume
28pub_type
杂志文章abstract：:Magnesium-based alloys exhibit biodegradable, biocompatible and excellent mechanical properties which enable them to serve as ideal candidate biomedical materials. In particular, their biodegradable ability helps patients to avoid a second surgery. The corrosion rate, however, is too rapid to sustain the healing proce...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章,评审
doi：10.1177/0885328219834656
更新日期：2019-05-01 00:00:00
abstract：:The development of an effective wound dressing with the ability to induce skin wound healing is a great challenge in medicine. Nanofibers are highly attractive for wound dressing preparation due to their properties such as hemostasis induction, good absorption of wound exudates, and facilitation of cell growth. Chitos...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328217739562
更新日期：2018-01-01 00:00:00
abstract：:Appropriate design of dialysis membranes requires correct values of structural parameters such as pore radius, surface porosity, water content and tortuosity. It is impossible, however, to find the pore radius of dialysis membranes using a mercury porosimeter or an electron microscope because the pores are only severa...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/088532828900400201
更新日期：1989-10-01 00:00:00
abstract：:To develop biocompatible composite microspheres for novel hemostatic use, we designed and prepared a novel biomaterial, composite microspheres consisting of carboxymethyl chitosan, sodium alginate, and collagen (CSCM). The ultra-structure of CSCM was investigated by scanning electron microscopy assay. In hemostatic fu...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328215618354
更新日期：2016-02-01 00:00:00
abstract：:Novel in situ polymerizable liquid three-arm biodegradable oligomeric polyesters based upon glycolic acid (GA), L-lactic acid (LLA), and their copolymers are synthesized and characterized. Injectable and in situ curable polymer neat resins and their composites formulated with bioabsorbable beta-tricalcium phosphate ar...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328206068691
更新日期：2007-07-01 00:00:00
abstract：:Single nanofibers with chemical and functional properties consistent with artery extracellular matrix nanofibers were produced by electrospinning. Using weight ratios to mimic artery extracellular matrix, five materials were tested: (1) Collagen type I, (2) Collagen type I + Collagen type III, (3) Collagen type I + po...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328213477893
更新日期：2014-01-01 00:00:00
abstract：:Devices such as contact lenses and collagen shields have been used to improve the antibiotic bioavailability of eye drops formulations in the treatment of ulcerative keratitis. Nevertheless, these devices are not sustained drug delivery systems, and a combination with eye drops is necessary. In animal patients, it req...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328220931733
更新日期：2020-09-01 00:00:00
abstract：:Antenna coupling microwave plasma enables a highly oxidative treatment of the outmost surface of polypropylene (PP) nonwoven fabric within a short time period. Subsequently, grafting copolymerization with acrylic acid (AAc) makes the plasma-treated fabric durably hydrophilic and excellent in water absorbency. With hig...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1106/088532802030478
更新日期：2002-10-01 00:00:00
abstract：:Glass Polyalkenoate Cements (GPCs) based on strontium calcium zinc silicate (Sr-Ca-Zn-SiO2) glasses and high molecular weight poly(acrylic acid) (PAA) have been shown to exhibit suitable mechanical properties for orthopaedic arthroplasty applications, however for vertebroplasty and other medical luting applications th...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328208099085
更新日期：2010-02-01 00:00:00
abstract：:Calcium polyphosphate is a biodegradable bone substitute. It remains a challenge to prepare porous calcium polyphosphate with desired gradient porous structures. In this study, a modified one-step gravity sintering method was used to prepare calcium polyphosphate scaffolds with desired-gradient-pore-size distribution....
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328215608335
更新日期：2016-02-01 00:00:00
abstract：:In this work, the role of shock wave-induced increase of bone morphogenetic proteins in modulating the osteogenic properties of osteoblast-like cells seeded on a bioactive scaffold was investigated using gremlin as a bone morphogenetic protein antagonist. Bone-like glass-ceramic scaffolds, based on a silicate experime...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328214541974
更新日期：2014-11-01 00:00:00
abstract：:Polymer biocomposites based on segmented poly(ester urethane) and extracellular matrix components have been prepared for the development of tissue engineering applications with improved biological characteristics of the materials in contact with blood and tissues for long periods. Thermal, dynamical, and dielectrical ...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328210394468
更新日期：2012-08-01 00:00:00
abstract：:Polylactic acid (PLA)-derived polymers are widely used in many biotechnological fields, thanks to their biocompatibility and resorbability through natural pathways. Moreover, PLA is one of the few polymers in which both the properties and the stereochemical structure can be easily modified, making possible a specific ...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328211398298
更新日期：2012-08-01 00:00:00
abstract：:Excessive demineralization in osteoporotic bones impairs its self-regeneration potential following a defect/fracture and is of great concern among the aged population. In this context, implants with inherent osteogenic ability loaded with therapeutic ions like Strontium (Sr2+) may bring forth promising outcomes. Micro...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328216647197
更新日期：2016-10-01 00:00:00
abstract：:The aim of the paper is to obtain and characterize k-carrageenan-chitosan dual hydrogel multilayers shell BSA gel microcapsules, as a carrier for curcumin, and as a possible antitumoral agent in biological studies. We used the CaCO3 template to synthesize non-toxic CaCO3/BSA particles as microtemplates by coprecipitat...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328215603797
更新日期：2016-01-01 00:00:00
abstract：:Chitosan-glutaraldehyde microparticles were produced by emulsion crosslinking method to be used as drug delivery system for polyphenols from Thymus serpyllum L. aqueous extract. The effect of preparation conditions, chitosan concentration (1.5-3% w/v), and glutaraldehyde/chitosan (GA/Ch) mass ratio (0.15-1.20) on wate...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328215598940
更新日期：2015-11-01 00:00:00
abstract：:While BMP-7 (OP-1) is one of the most potent growth factors in cartilage tissue engineering, the effects of exogenous low concentration BMP-7 on osteoarthritic chondrocytes are still unknown. Human osteoarthritic chondrocytes obtained from the femoral condyles of 10 patients were grown either in monolayer or in 3D col...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328210388439
更新日期：2012-03-01 00:00:00
abstract：:The aim of this study was to examine the release of silica (Si), calcium (Ca), phosphorous (P), and fluoride (F) from conventional glass ionomer cement (GI) and resin-modified glass ionomer cement (LCGI), containing different quantities of bioactive glass (BAG). Further aim was to evaluate in vitro biomineralization o...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0085328204044538
更新日期：2004-07-01 00:00:00
abstract：:The controlled release of insulin from a series of biodegradable hybrid hydrogel network containing dextran derivative of allyl isocyanate (dex-AI) and poly (D,L) lactide diacrylate macromer (PDLLAM) over a wide range of composition ratio was investigated. Laser confocal scanning microscope was used to understand the ...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1106/088532802024248
更新日期：2002-04-01 00:00:00
abstract：:This study reports the properties of tableted microparticles based on high-amylose corn starch (HACS)-pectin blend polymers as the controlled release system for diclofenac sodium (DS). HACS-pectin blend microparticles are prepared through a modified process by the spray drying technique, which is a widely used microen...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328206056771
更新日期：2007-01-01 00:00:00
abstract：:Hydrogels were prepared from 2-hydroxyethyl methacrylate and ethylene glycol dimethacrylate as cross-linking agent. Two different polymerization techniques were followed, namely bulk polymerization initiated by dibenzoyl peroxide and solution polymerization, in water, using a redox initiator system. Differences in the...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/088532829801200402
更新日期：1998-04-01 00:00:00
abstract：:Carbon-fibre-reinforced polyether ether ketone (CFR-PEEK) exhibits excellent biomechanical properties as it has an elastic modulus similar to bone. However, CFR-PEEK displays inferior biocompatibility compared with titanium alloy and coating techniques are therefore of interest in order to improve integration. In this...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328214521669
更新日期：2014-08-01 00:00:00
abstract：:Sustained intestinal delivery of thiamine hydrochloride (Vitamin B(1); VB(1)) and pyridoxine hydrochloride (Vitamin B(6); VB(6)) seems to be a feasible alternative to existing therapy. The vitamins (VB(1)/VB(6)) intercalated in montmorillonite (MMT) and intercalated VB(1)/VB(6)-MMT hybrid is further used for synthesis...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328209344003
更新日期：2010-08-01 00:00:00
abstract：:A rapid and continuous hydrothermal route for the synthesis of nano-sized hydroxyapatite rods co-precipitated with calcium-doped zirconia nanoparticles using a superheated water flow at 450°C and 24.1 MPa as a crystallizing medium is described. Hydroxyapatite and calcium-doped zirconia phases in the powder mixtures co...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328212444483
更新日期：2012-07-01 00:00:00
abstract：:An experimental and computational investigation of the self-tapping ability of carbon fibre reinforced polyetheretherketone (CFR-PEEK) has been conducted. Six CFR-PEEK suture anchor designs were investigated using PEEK-OPTIMA® Reinforced, a medical grade of CFR-PEEK. Experimental tests were conducted to investigate th...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328214535274
更新日期：2014-10-01 00:00:00
abstract：:NiTi alloy is used as a biomaterial due to its pseudoelastic behaviour. It exhibits a great potential in dental and orthopedic applications where constant correcting loads are required. In order to use such materials, it is necessary to investigate the effect of the cyclic straining upon the transformation stresses an...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/088532829801200304
更新日期：1998-01-01 00:00:00
abstract：:In the present study, a novel hydrogel-grafted fabrics embedding of berberine nanosuspension was developed for the treatment of infected wound. Hydrogel-grafted fabric was prepared by graft copolymerization of N-isopropylacrylamide and alginate using ceric ammonium nitrate as initiator. Berberine nanosuspension was pr...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328213509503
更新日期：2014-05-01 00:00:00
abstract：:Among biomaterials used as implants in human body, sutures constitute the largest groups of materials having a huge market exceeding $1.3 billion annually. Sutures are the most widely used materials in wound closure and have been in use for many centuries. With the development of the synthetic absorbable polymer, poly...
journal_title：Journal of biomaterials applications
pub_type： 历史文章,杂志文章,评审
doi：10.1177/0885328210384890
更新日期：2010-11-01 00:00:00
abstract：:Fabrication of osteoconductive scaffold with osteoinductive capability and appropriate resorption rate is of great significance for treating bone defects. To achieve this aim, strontium-substituted calcium sulfate hemihydrate (Sr-CSH) and hydroxyapatite (HA) were mixed to develop a novel composite. Sr-CSH containing 5...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328220915816
更新日期：2020-07-01 00:00:00
abstract：:Calcium phosphate fillers have been shown to increase cement osteoconductivity, but have caused drawbacks in cement properties. Hydroxyapatite and Brushite were introduced in an acrylic two-solution cement at varying concentrations. Novel composite bone cements were developed and characterized using rheology, injectab...
journal_title：Journal of biomaterials applications
pub_type： 杂志文章
doi：10.1177/0885328214544770
更新日期：2014-11-01 00:00:00
