Monitoring industrial pharmaceutical crystallization processes using acoustic emission in pure and impure media.

Abstract:

:Acoustic emission (AE) which has been successfully applied for monitoring a rather wide variety of solids elaboration processes was almost never evaluated in the field of industrial pharmaceutical crystallization. Few papers reported that solution crystallization processes give rise to acoustic emission signals that could be related to the development of the basic crystallization phenomena. This study is intended to demonstrate new perspectives opened up by the possible use of acoustic emission (AE) as a non-intrusive and non destructive sensor for monitoring solution crystallization with a particular focus being put on the presence of impurities in real industrial processes. The wealth of acquired AE information is highlighted and it is suggested that such information could allow the design of innovative multipurpose sensing strategies. It is shown notably that AE provides a very early detection of nucleation events, much before the onset of the so-called "nucleation burst". It is also shown that AE brings new insight into the effect of impurities on both the development of the crystallization process and the quality of the crystallized product.

journal_name

Int J Pharm

authors

Gherras N,Serris E,Fevotte G

doi

10.1016/j.ijpharm.2012.09.048

subject

Has Abstract

pub_date

2012-12-15 00:00:00

pages

109-19

issue

1-2

eissn

0378-5173

issn

1873-3476

pii

S0378-5173(12)00922-2

journal_volume

439

pub_type

杂志文章
  • Preparation of surface modified protein nanoparticles by introduction of sulfhydryl groups.

    abstract::The objective of the present study was to establish several methods for the introduction of thiol groups onto the surface of human serum albumin (HSA) nanoparticles. Besides the epsilon-amino groups of lysine, the carboxyl groups of asparaginic and glutaminic acid, and the carbonyl groups of the cross-linker glutarald...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/s0378-5173(00)00590-1

    authors: Weber C,Reiss S,Langer K

    更新日期:2000-12-15 00:00:00

  • WITHDRAWN: Microfabrication of dissolvable, swellable, and biodegradable polymeric microneedle arrays.

    abstract::This article has been withdrawn at the request of the authors. The Publisher apologizes for any inconvenience this may cause. The full Elsevier Policy on Article Withdrawal can be found at http://www.elsevier.com/locate/withdrawalpolicy. ...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2012.11.046

    authors: Demir YK,Akan Z,Kerimoglu O

    更新日期:2012-12-20 00:00:00

  • Preparation and optimization of fisetin loaded glycerol based soft nanovesicles by Box-Behnken design.

    abstract::The present study focused on the development and optimization of glycerosomes for dermal delivery of fisetin. The fisetin loaded glycerosomes formulation was optimized by Box-Behnken design. The independent variables were the lipoid S 100, glycerol, and sonication time, whereas the dependent variables were the vesicle...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2020.119125

    authors: Moolakkadath T,Aqil M,Ahad A,Imam SS,Praveen A,Sultana Y,Mujeeb M

    更新日期:2020-03-30 00:00:00

  • Thermal analysis of the crystallization and melting behavior of lipid matrices and lipid nanoparticles containing high amounts of lecithin.

    abstract::Lipid nanoparticles (LNP) based on triglycerides containing high amounts of the amphiphilic lipid lecithin have been proposed as a promising alternative drug delivery system with regard to drug loading capacity. Aim of the present study is to evaluate the influence of lecithin within the lipid matrix (LM) on the cryst...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2005.04.014

    authors: Schubert MA,Schicke BC,Müller-Goymann CC

    更新日期:2005-07-14 00:00:00

  • In vitro experiment optimization for measuring tetrahydrocannabinol skin permeation.

    abstract::The purpose of this study was to optimize in vitro experimental conditions for the measurement of Delta(9)-tetrahydrocannabinol (Delta(9)-THC) permeation across human skin using a flow-through diffusion cell system. The drug permeation rates through intact and stripped (stratum corneum (SC) removed) skin were also com...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/s0378-5173(02)00262-4

    authors: Challapalli PV,Stinchcomb AL

    更新日期:2002-07-25 00:00:00

  • Characterization and compaction behaviour of nimesulide crystal forms.

    abstract::Nimesulide is a typical nonsteroidal anti-inflammatory drug (NSAID), widely used in solid oral formulations. By crystallizing nimesulide from an ethanol solution a crystalline form was obtained, different from the reference sample, as confirmed by X-ray powder diffraction (XRPD), Differential Scanning Calorimetry (DSC...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2007.05.009

    authors: Di Martino P,Censi R,Barthélémy C,Gobetto R,Joiris E,Masic A,Odou P,Martelli S

    更新日期:2007-09-05 00:00:00

  • Localized drug delivery with mono and bilayered mucoadhesive films and wafers for oral mucosal infections.

    abstract::Local drug delivery into oral cavity offers many advantages over systemic administration in treatment of the oral infections. In this study, monolayer and bilayered mucoadhesive film and wafer formulations were developed as local drug delivery platforms using chitosan and hydroxypropyl methylcellulose (HPMC). Cefuroxi...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2019.01.029

    authors: Timur SS,Yüksel S,Akca G,Şenel S

    更新日期:2019-03-25 00:00:00

  • Sustained release coating of tablets with Eudragit(®) RS/RL using a novel electrostatic dry powder coating process.

    abstract::The objectives of this study were to develop an electrostatic dry powder coating process for sustained coating tablets with Eudragit(®) RS/RL and to investigate the effects of various factors and operating conditions on the coating process and drug release profile. A liquid plasticizer (triethyl citrate) was sprayed o...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2010.07.047

    authors: Qiao M,Luo Y,Zhang L,Ma Y,Stephenson TS,Zhu J

    更新日期:2010-10-31 00:00:00

  • Pluronic gels for nasal delivery of Vitamin B12. Part I: preformulation study.

    abstract::Thermoreversible nasal gels of Vitamin B(12) using pluronic PF 127 were aimed to improve absorption and patient compliance. In the present research work, effects of Vitamin B(12) and gel additives, viz. PF concentration, osmolarity, polyethylene glycol (PEG 15000) on thermodynamic properties of phase transitions at ge...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2003.10.005

    authors: Pisal SS,Paradkar AR,Mahadik KR,Kadam SS

    更新日期:2004-02-11 00:00:00

  • Use of ultrasound to prepare lipid emulsions of lorazepam for intravenous injection.

    abstract::Lipid emulsions can be used as a vehicle for the production of low-volume injectable preparations with minimally water-soluble active ingredients. First, we focus on the galenic and technological conditions established by ultrasound techniques. A 2(5) factorial design was used to optimize the carrier emulsion. The stu...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/s0378-5173(00)00664-5

    authors: Medina J,Salvadó A,del Pozo A

    更新日期:2001-03-23 00:00:00

  • Tablet splitting: Product quality assessment of metoprolol succinate extended release tablets.

    abstract::Metoprolol succinate extended release tablets comprise a multiple unit system containing metoprolol succinate in a multitude of controlled release pellets. Each pellet acts as a separate drug delivery unit and is designed to deliver metoprolol continuously over the dosage interval. Despite the flexibility that control...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2010.09.004

    authors: Zhao N,Zidan A,Tawakkul M,Sayeed VA,Khan M

    更新日期:2010-11-30 00:00:00

  • In vitro and in vivo characterization of nanoparticles made of MeO-PEG amine/PLA block copolymer and PLA.

    abstract::The preparative method of a block copolymer of poly(dl-lactic acid) (PLA) and methoxypolyethylene glycol amine (MeO-PEG(N)), named PLA-(MeO-PEG), was refined. The degree of introduction of MeO-PEG(N) into PLA increased up to 55% (mol/mol) using a dichloromethane/methanol mixture (1:1, v/v) as a solvent at the reductiv...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2006.02.057

    authors: Sasatsu M,Onishi H,Machida Y

    更新日期:2006-07-24 00:00:00

  • BCNU-loaded poly(D, L-lactide-co-glycolide) wafer and antitumor activity against XF-498 human CNS tumor cells in vitro.

    abstract::Implantable polymeric device that can release chemotherapeutic agent directly into central nervous system (CNS) has had an impact on malignant glioma therapy. The purpose of our study was to develop an implantable polymeric device, which can release intact 1,3-bis(2-chloroethyl)-1-nitrosourea (BCNU) for long-term peri...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/s0378-5173(02)00543-4

    authors: Seong H,An TK,Khang G,Choi SU,Lee CO,Lee HB

    更新日期:2003-01-30 00:00:00

  • Non-linear mixed effects models for the evaluation of dissolution profiles.

    abstract::The use of non-linear mixed effects models to describe dissolution data has been evaluated. A theoretical part is included to introduce this approach to scientists who are not familiar with this type of statistics. The standard settings of the statistical software package (S-plus) are used as much as possible. Several...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/s0378-5173(02)00127-8

    authors: Adams E,Coomans D,Smeyers-Verbeke J,Massart DL

    更新日期:2002-06-20 00:00:00

  • Thermal dose as a universal tool to evaluate nanoparticle-induced photothermal therapy.

    abstract::Thermal isoeffect dose (TID) is a widely applied concept to evaluate the safety of medical devices that can expose patients to heat. However, it has rarely been used in photothermal therapy (PTT), where nanoparticles are used as light absorbers. Utilizing TID in an appropriate way would make it feasible to compare the...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2020.119657

    authors: Happonen E,Tamarov K,Martikainen MV,Ketola K,Roponen M,Lehto VP,Xu W

    更新日期:2020-09-25 00:00:00

  • Preparation of osthole-polymer solid dispersions by hot-melt extrusion for dissolution and bioavailability enhancement.

    abstract::The aim of this study was to investigate the potential of solid dispersion to improve the dissolution rate and bioavailability of osthole (Ost), a coumarin derivative with various pharmacological activities but with poor aqueous solubility. In present studies, the Ost solid dispersions were prepared with various polym...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2014.02.040

    authors: Yun F,Kang A,Shan J,Zhao X,Bi X,Li J,Di L

    更新日期:2014-04-25 00:00:00

  • Formulating powder-device combinations for salmeterol xinafoate dry powder inhalers.

    abstract::Using salmeterol xinafoate (SX) as an active pharmaceutical ingredient, the effects of carrier lactose particle type, total lactose fines content and device resistance on dry powder inhaler performance were investigated in vitro. To mimic drug levels in commercial preparations, interactive mixtures containing 0.58% w/...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2015.05.028

    authors: Hassoun M,Ho S,Muddle J,Buttini F,Parry M,Hammond M,Forbes B

    更新日期:2015-07-25 00:00:00

  • Contribution of TRPV1 and multidrug resistance proteins in the permeation of capsaicin across different intestinal regions.

    abstract:OBJECTIVE:The aim of the study was to observe the characteristic of permeation of capsaicin across jejunum, ileum and colon in the rat, and to investigate the role of transient receptor potential cation channel (TRPV1). The interaction of capsaicin with P-glycoprotein (P-gp), multidrug resistance-associated protein 2 (...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2013.02.007

    authors: Duan L,Yan Y,Sun Y,Zhao B,Hu W,Li G

    更新日期:2013-03-10 00:00:00

  • Incorporation of benzoyl peroxide nanocrystals into adapalene-loaded solid lipid microparticles: Part II - Solid-in-Oil dispersion of nanoparticulate benzoyl peroxide.

    abstract::Benzoyl peroxide as a monotherapeutic and in combination with adapalene is a cornerstone of current acne therapy, but its unfavourable side effect profile reduces the therapeutic value of this compound. The incorporation into an adapalene-loaded microparticulate lipid matrix, which - via the principle of targeted eros...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2019.118792

    authors: Brammann C,Müller-Goymann CC

    更新日期:2019-12-15 00:00:00

  • Production and evaluation of size reduced grades of microcrystalline cellulose.

    abstract::Size reduction of microcrystalline cellulose (MCC, Avicel PH-101) powder by ball milling was poorly effective, particularly in the presence of sodium lauryl sulphate (SLS), which tended to form a protective foam. Ultrasonic homogenisation of an aqueous suspension more readily produced ultra-fine MCC, even in the prese...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/s0378-5173(00)00652-9

    authors: Levis SR,Deasy PB

    更新日期:2001-02-01 00:00:00

  • Predicting the gastrointestinal behaviour of modified-release products: utility of a novel dynamic dissolution test apparatus involving the use of bicarbonate buffers.

    abstract::The establishment of physiologically relevant in vitro-in vivo correlations (IV-IVCs) is key for any biorelevant dissolution test. Historically, bicarbonate buffers have produced better correlations than compendial phosphate buffered media, though such tests are usually performed at a constant pH experiment, overlooki...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2014.09.003

    authors: Merchant HA,Goyanes A,Parashar N,Basit AW

    更新日期:2014-11-20 00:00:00

  • Process characterisation, optimisation and validation of production of diacetylmorphine/caffeine sachets: a design of experiments approach.

    abstract::Powder filled sachets containing a 3:1 (w/w) powder mixture of diacetylmorphine base and caffeine anhydrate were developed as a dosage form for smokable heroin used for the treatment of chronic, treatment-resistant heroin addicts. The powder mixture was filled into sachets using a micro dose auger filler machine. The ...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2004.07.007

    authors: Klous MG,Nuijen B,Van den Brink W,Van Ree JM,Beijnen JH

    更新日期:2004-11-05 00:00:00

  • The quantification of small degrees of disorder in lactose using solution calorimetry.

    abstract::There is a realisation that small quantities of amorphous material can have a significant impact on the properties of crystalline solids. Consequently there is a growing interest in quantifying the amount of amorphous material that is present in "crystalline powders". Success has been reported when using isothermal mi...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/s0378-5173(00)00527-5

    authors: Hogan SE,Buckton G

    更新日期:2000-10-10 00:00:00

  • Potency of select statin drugs in a new mouse model of hyperlipidemia and atherosclerosis.

    abstract::Poloxamer-407 (P-407) is a nonionic surfactant that induces atheroma formation in the aortas of C57BL/6 mice with long-term (14 weeks) administration. The objectives of the present study were to determine the mechanism(s) responsible for the induction of hypercholesterolemia as well as to determine whether this animal...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/s0378-5173(01)00834-1

    authors: Johnston TP,Nguyen LB,Chu WA,Shefer S

    更新日期:2001-10-23 00:00:00

  • Development of a controlled release formulation based on SLN and NLC for topical clotrimazole delivery.

    abstract::Solid lipid nanoparticles (SLN) and nanostructured lipid carriers (NLC) are colloidal carrier systems providing controlled release profiles for many substances. Clotrimazole-loaded SLN and NLC were prepared by the hot high pressure homogenization technique in order to evaluate the physical stability of these particles...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2004.02.032

    authors: Souto EB,Wissing SA,Barbosa CM,Müller RH

    更新日期:2004-06-18 00:00:00

  • Pore blocking: An innovative formulation strategy for the design of alcohol resistant multi-particulate dosage forms.

    abstract::In this work calcium stearate (CaSt) multi-particulates loaded with codeine phosphate (COP) were developed in an attempt to provide extended release (ER) combined with alcohol dose dumping (ADD) resistance. The pellets were prepared via wet/extrusion spheronization and ER characteristics were obtained after fluid bed ...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2016.05.049

    authors: Schrank S,Jedinger N,Wu S,Piller M,Roblegg E

    更新日期:2016-07-25 00:00:00

  • Preparation and characterization of teniposide PLGA nanoparticles and their uptake in human glioblastoma U87MG cells.

    abstract::Many studies have demonstrated the uptake mechanisms of various nanoparticle delivery systems with different physicochemical properties in different cells. In this study, we report for the first time the preparation and characterization of teniposide (VM-26) poly(D,L-lactide-co-glycolide) (PLGA) nanoparticles (NPs) an...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2012.07.050

    authors: Mo L,Hou L,Guo D,Xiao X,Mao P,Yang X

    更新日期:2012-10-15 00:00:00

  • Distribution of salicylic acid in human stratum corneum following topical application in vivo: a comparison of six different formulations.

    abstract::Distribution of salicylic acid in human stratum corneum from treatment of six different formulations was assessed by quantitation of drug content in sequentially tape-stripped stratum corneum after a single 2-h dose was applied unoccluded to skin on the ventral forearm of four female subjects. The profile and total am...

    journal_title:International journal of pharmaceutics

    pub_type: 临床试验,杂志文章,随机对照试验

    doi:10.1016/s0378-5173(99)00217-3

    authors: Tsai J,Chuang S,Hsu M,Sheu H

    更新日期:1999-10-25 00:00:00

  • Evaluating particle hardness of pharmaceutical solids using AFM nanoindentation.

    abstract::Understanding mechanical properties of pharmaceutical solids at the submicron scale can be very important to pharmaceutical research & development. In this paper, the hardness of individual particles of various pharmaceutical solids including sucrose, lactose, ascorbic acid, and ibuprofen was quantified using the atom...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章

    doi:10.1016/j.ijpharm.2008.06.015

    authors: Masterson VM,Cao X

    更新日期:2008-10-01 00:00:00

  • Sterilization of implantable polymer-based medical devices: A review.

    abstract::This review article is focused on the sterilization techniques used for polymer-based implantable medical devices as well as the regulatory aspects governing sterile medical devices. Polymeric materials are increasingly used in implantable devices due to their biodegradable and biocompatible nature. Patients and medic...

    journal_title:International journal of pharmaceutics

    pub_type: 杂志文章,评审

    doi:10.1016/j.ijpharm.2017.12.003

    authors: Tipnis NP,Burgess DJ

    更新日期:2018-06-15 00:00:00