Self-initiated surface grafting with poly(2-methacryloyloxyethyl phosphorylcholine) on poly(ether-ether-ketone).

Abstract:

:Poly(ether-ether-ketone) (PEEK)s are a group of polymeric biomaterials with excellent mechanical properties and chemical stability. In the present study, we demonstrate the fabrication of an antibiofouling and highly hydrophilic high-density nanometer-scaled layer on the surface of PEEK by photo-induced graft polymerization of 2-methacryloyloxyethyl phosphorylcholine (MPC) without using any photo-initiators, i.e., "self-initiated surface graft polymerization." Our results indicated that the diphenylketone moiety in the polymer backbone acted as a photo-initiator similar to benzophenone. The density and thickness of the poly(MPC) (PMPC)-grafted layer were controlled by the photo-irradiation time and monomer concentration during polymerization, respectively. Since MPC is a highly hydrophilic compound, the water wettability (contact angle <10 degrees) and lubricity (coefficient of dynamic friction <0.01) of the PMPC-grafted PEEK surface were considerably lower than those of the untreated PEEK surface (90 degrees and 0.20, respectively) due to the formation of a PMPC nanometer-scale layer. In addition, the amount (0.05 microg/cm(2)) of BSA adsorbed on the PMPC-grafted PEEK surface was considerably lower, that is more than 90% reduction, compared to that (0.55 microg/cm(2)) for untreated PEEK. This photo-induced polymerization process occurs only on the surface of the PEEK substrate; therefore, the desirable mechanical properties of PEEK would be maintained irrespective of the treatment used.

journal_name

Biomaterials

journal_title

Biomaterials

authors

Kyomoto M,Moro T,Takatori Y,Kawaguchi H,Nakamura K,Ishihara K

doi

10.1016/j.biomaterials.2009.10.055

subject

Has Abstract

pub_date

2010-02-01 00:00:00

pages

1017-24

issue

6

eissn

0142-9612

issn

1878-5905

pii

S0142-9612(09)01176-4

journal_volume

31

pub_type

杂志文章
  • In vivo measurement of anodic polarization of orthopaedic implant alloys: comparative study of in vivo and in vitro experiments.

    abstract::A new system of single piece electrodes was applied to in vivo and in vitro measurements of anodic polarization of several alloys used in orthopaedic implants. The tested surface was scrutinized with a stereomicroscope after each experiment. This confirmed pit formation and excluded the possibility of other sudden inc...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/0142-9612(89)90134-8

    authors: Nakayama Y,Yamamuro T,Kotoura Y,Oka M

    更新日期:1989-08-01 00:00:00

  • Fabrication of hydroxyapatite sponges by dextran sulphate/amino acid templating.

    abstract::We report a new template-directed method for the fabrication of hydroxyapatite (HAp) sponges by using amino-acid-coated HAp nanoparticles dispersed within a viscous polysaccharide (dextran sulfate) matrix, and describe the use of these materials for the viability and proliferation of human bone marrow stromal cells. T...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2005.04.037

    authors: Gonzalez-McQuire R,Green D,Walsh D,Hall S,Chane-Ching JY,Oreffo RO,Mann S

    更新日期:2005-11-01 00:00:00

  • Spinal cord repair with PHPMA hydrogel containing RGD peptides (NeuroGel).

    abstract::A biocompatible hydrogel of poly[N-(2-hydroxypropyl)methacrylamide] (PHPMA) which includes the cell-adhesive region of fibronectin Arg-Gly-Asp was synthesized and its structure, rheological and dielectric properties were characterized. The ability of a PHPMA-RGD hydrogel to promote tissue regeneration and support axon...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/s0142-9612(00)00354-9

    authors: Woerly S,Pinet E,de Robertis L,Van Diep D,Bousmina M

    更新日期:2001-05-01 00:00:00

  • Long-term stability in vivo of a thromboresistant heparinized surface.

    abstract::A surface with covalently bonded heparin was tested in an in vivo model. Heparinized and non-heparinized tubings were inserted in the pig aorta. They were left in place for up to 16 wk. After removal they were analysed for their capacity to take up and inhibit thrombin. A comparison was also made with tubings that had...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/0142-9612(87)90088-3

    authors: Arnander C,Bagger-Sjöbäck D,Frebelius S,Larsson R,Swedenborg J

    更新日期:1987-11-01 00:00:00

  • Varying PEG density to control stress relaxation in alginate-PEG hydrogels for 3D cell culture studies.

    abstract::Hydrogels are commonly used as artificial extracellular matrices for 3D cell culture and for tissue engineering. Viscoelastic hydrogels with tunable stress relaxation have recently been developed, and stress relaxation in the hydrogels has been found to play a key role in regulating cell behaviors such as differentiat...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2019.02.004

    authors: Nam S,Stowers R,Lou J,Xia Y,Chaudhuri O

    更新日期:2019-04-01 00:00:00

  • Properties of heat-treated calcium phosphate coatings deposited by high-velocity oxy-fuel (HVOF) spray.

    abstract::The influence of crystallization, upon heat treatment, on the properties of high-velocity oxy-fuel (HVOF) sprayed hydroxyapatite (HA) coatings was investigated. The characterization of the HA coating was performed by X-ray diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FTIR). Differential Scanning Calo...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/s0142-9612(01)00326-x

    authors: Li H,Khor KA,Cheang P

    更新日期:2002-05-01 00:00:00

  • Capture of endothelial cells under flow using immobilized vascular endothelial growth factor.

    abstract::We demonstrate the ability of immobilized vascular endothelial growth factor (VEGF) to capture endothelial cells (EC) with high specificity under fluid flow. To this end, we engineered a surface consisting of heparin bound to poly-l-lysine to permit immobilization of VEGF through the C-terminal heparin-binding domain....

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2015.02.025

    authors: Smith RJ Jr,Koobatian MT,Shahini A,Swartz DD,Andreadis ST

    更新日期:2015-05-01 00:00:00

  • SPARC-derived protease substrates to enhance the plasmin sensitivity of molecularly engineered PEG hydrogels.

    abstract::Bioactive hydrogels formed from the Michael-type addition reactions of end-functionalized poly (ethylene glycol) macromers with thiol-containing protease-sensitive peptide crosslinkers have previously been described as matrices for cell-induced enzymatic remodeling. In this study, we sought to develop materials formul...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2010.10.016

    authors: Patterson J,Hubbell JA

    更新日期:2011-02-01 00:00:00

  • A novel soft tissue model for biomaterial-associated infection and inflammation - bacteriological, morphological and molecular observations.

    abstract::Infection constitutes a major risk for implant failure, but the reasons why biomaterial sites are more vulnerable than normal tissue are not fully elucidated. In this study, a soft tissue infection model was developed, allowing the analysis of cellular and molecular responses in each of the sub-compartments of the imp...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2014.11.032

    authors: Svensson S,Trobos M,Hoffman M,Norlindh B,Petronis S,Lausmaa J,Suska F,Thomsen P

    更新日期:2015-02-01 00:00:00

  • Cellular uptake and activity of heparin functionalised cerium oxide nanoparticles in monocytes.

    abstract::Cerium oxide nanoparticles (nanoceria) are effective in scavenging intracellular reactive oxygen species (ROS). In this study nanoceria synthesized by flame spray pyrolysis (dXRD = 12 nm) were functionalised with heparin via an organosilane linker, 3-aminopropyltriethoxysilane. Nanoceria were functionalised with appro...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2013.02.042

    authors: Ting SR,Whitelock JM,Tomic R,Gunawan C,Teoh WY,Amal R,Lord MS

    更新日期:2013-06-01 00:00:00

  • The effect of multifunctional polymer-based gels on wound healing in full thickness bacteria-contaminated mouse skin wound models.

    abstract::We determined whether a two-part space-conforming polyethylene glycol/dopa polymer-based gel promoted healing of contaminated wounds in mice. This silver-catalysed gel was previously developed to be broadly microbiocidal in vitro while being biocompatible with human wound cell functioning. Full-thickness wounds were c...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2007.05.008

    authors: Yates CC,Whaley D,Babu R,Zhang J,Krishna P,Beckman E,Pasculle AW,Wells A

    更新日期:2007-09-01 00:00:00

  • A 3D tumor microenvironment regulates cell proliferation, peritoneal growth and expression patterns.

    abstract::Peritoneal invasion through the mesothelial cell layer is a hallmark of ovarian cancer metastasis. Using tissue engineering technologies, we recreated an ovarian tumor microenvironment replicating this aspect of disease progression. Ovarian cancer cell-laden hydrogels were combined with mesothelial cell-layered melt e...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2018.10.014

    authors: Loessner D,Rockstroh A,Shokoohmand A,Holzapfel BM,Wagner F,Baldwin J,Boxberg M,Schmalfeldt B,Lengyel E,Clements JA,Hutmacher DW

    更新日期:2019-01-01 00:00:00

  • Lithography application of a novel photoresist for patterning of cells.

    abstract::Photolithography is the current workhorse for the microelectronic industry. It has been used extensively for the creation of patterns on two-dimensional surfaces. Various research groups have studied the use of photolithography to pattern surfaces for the alignment of cells. So far, these applications have been limite...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2003.08.055

    authors: He W,Halberstadt CR,Gonsalves KE

    更新日期:2004-05-01 00:00:00

  • Control of the formation of vascular networks in 3D tissue engineered constructs.

    abstract::Construction of bio-mimetic well-organized three-dimensional (3D) tissue with various cells in vitro is one of the ultimate goals of tissue engineering. In particular, fabrication of vasculature in 3D tissue is one of the most important tasks in tissue engineering, because a vascular network is indispensable for almos...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2012.10.009

    authors: Muraoka M,Shimizu T,Itoga K,Takahashi H,Okano T

    更新日期:2013-01-01 00:00:00

  • Processes human umbilical veins as arterial substitutes--evaluation in canine models.

    abstract::Human umbilical cord vein segments have been used as vessel substitutes for damaged or occluded arteries, as aorto-coronary by-passes and as arterio-venous fistulae for dialysis. The Dardik-Biograft fixed with glutaraldehyde and the Mindich-Bioflow, fixed with ethanol and dialdehyde starch, are commercially available....

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/0142-9612(80)90004-6

    authors: Guidoin R,Marois M,Martin L,Noël HP,Laroche F,Gosselin CO,Côté R,Bénichoux R,Blais P

    更新日期:1980-04-01 00:00:00

  • Non-destructive label-free monitoring of collagen gel remodeling using optical coherence tomography.

    abstract::Matrix remodeling plays a fundamental role in physiological and pathological processes, as well as in tissue engineering applications. In this paper, optical coherence tomography (OCT), a non-destructive optical imaging technology, was used to image collagen gel remodeling by smooth muscle cells (SMCs). The optical sc...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2010.06.042

    authors: Levitz D,Hinds MT,Ardeshiri A,Hanson SR,Jacques SL

    更新日期:2010-11-01 00:00:00

  • Thermal dimensional behavior of dental ceramics.

    abstract::The aim of this study was to characterize the relation of dimensional changes of dental ceramic materials as function of temperature. The thermal dimensional behavior of one glass ceramic core, four commercially available veneering porcelains and two experimental veneering porcelain materials was determined on cooling...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2003.09.027

    authors: Isgrò G,Kleverlaan CJ,Wang H,Feilzer AJ

    更新日期:2004-05-01 00:00:00

  • Geometric control of capillary architecture via cell-matrix mechanical interactions.

    abstract::Capillary morphogenesis is a multistage, multicellular activity that plays a pivotal role in various developmental and pathological situations. In-depth understanding of the regulatory mechanism along with the capability of controlling the morphogenic process will have direct implications on tissue engineering and the...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2013.12.101

    authors: Sun J,Jamilpour N,Wang FY,Wong PK

    更新日期:2014-03-01 00:00:00

  • Promotion of cardiac differentiation of brown adipose derived stem cells by chitosan hydrogel for repair after myocardial infarction.

    abstract::The ability to restore heart function by replacement of diseased myocardium is one of the great challenges in biomaterials and regenerative medicine. Brown adipose derived stem cells (BADSCs) present a new source of cardiomyocytes to regenerate the myocardium after infarction. In this study, we explored an injectable ...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2014.01.021

    authors: Wang H,Shi J,Wang Y,Yin Y,Wang L,Liu J,Liu Z,Duan C,Zhu P,Wang C

    更新日期:2014-04-01 00:00:00

  • Morphometric and microanalytical analyses of alumina wear particles in hip prostheses.

    abstract::We analysed tissues harvested during 24 retrievals of hip joint prostheses, with one or both articular components made of alumina. We describe the morphology of wear particles, measure their size and analyse their chemical composition. We relate histopathological aspects to the parameters that characterize ceramic wea...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/0142-9612(93)90175-2

    authors: Pizzoferrato A,Stea S,Sudanese A,Toni A,Nigrisoli M,Gualtieri G,Squarzoni S

    更新日期:1993-07-01 00:00:00

  • The effect of squalane-dissolved fullerene-C60 on adipogenesis-accompanied oxidative stress and macrophage activation in a preadipocyte-monocyte co-culture system.

    abstract::Effects of squalane-dissolved fullerene-C60 (Sql-fullerene) on macrophage activation and adipose conversion with oxidative stress were studied using an inflammatory adipose-tissue equivalent (ATE) and OP9 mouse stromal preadipocyte-U937 lymphoma cell co-culture systems. Differentiation of OP9 cells was initiated by in...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2010.04.032

    authors: Xiao L,Aoshima H,Saitoh Y,Miwa N

    更新日期:2010-08-01 00:00:00

  • pH-sensitive hydrogels based on non-ionic acrylic copolymers.

    abstract::Hydrogels based on ethoxytriethyleneglycol monomethacrylate/methyl methacrylate copolymers were prepared by free radical polymerization at 70 degrees C in bulk with 2,2'-azobisisobutyronitrile as initiator. The swelling behaviour of the hydrogels was studied by immersion of the films in water and in buffered solutions...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/s0142-9612(96)00091-9

    authors: Vázquez B,Gurruchaga M,Goñi I,San Román J

    更新日期:1997-04-01 00:00:00

  • Biaxial strength of multilaminated extracellular matrix scaffolds.

    abstract::Xenogeneic extracellular matrix (ECM) can be harvested and configured to function as a bioscaffold for tissue and organ reconstruction. The mechanical properties of the ECM vary depending upon the tissue from which it is harvested. Likewise, the manufacturing steps required to develop ECMs into medical grade devices w...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2003.09.015

    authors: Freytes DO,Badylak SF,Webster TJ,Geddes LA,Rundell AE

    更新日期:2004-05-01 00:00:00

  • Tissue response to polyanionic collagen: elastin matrices implanted in rat calvaria.

    abstract::The tissue response to polyanionic collagen matrices, prepared from bovine pericardium and implanted subperiosteally in rat calvaria, was studied. The materials were implanted in 72 male rats (Rattus norvegicus, albinus, Holtzman), randomly divided into four groups: GI-MBP hydrolyzed for 24 h; GII-MBP hydrolyzed for 3...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/s0142-9612(02)00292-2

    authors: Rosa FP,Lia RC,de Souza KO,Goissis G,Marcantonio E Jr

    更新日期:2003-01-01 00:00:00

  • Sensitivity to implant materials in patients with total knee arthroplasties.

    abstract::Materials used for total knee arthroplasty (TKA), may elicit an immune response whose role in the outcome of the arthroplasty is still unclear. The aim of this study was to evaluate the frequency of sensitization in patients who had undergone TKA, and the clinical impact of this event on the outcome of the implant. Ni...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2007.11.038

    authors: Granchi D,Cenni E,Tigani D,Trisolino G,Baldini N,Giunti A

    更新日期:2008-04-01 00:00:00

  • Structure of dental gallium alloys.

    abstract::The interest in gallium alloys as a replacement for amalgam has increased in recent years due to the risk of environmental pollution from amalgam. Alloy powders with compositions close to those for alloys of amalgam are mixed with a liquid gallium alloy. The mix is condensed into a prepared cavity in much the same way...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:

    authors: Herø H,Simensen CJ,Jørgensen RB

    更新日期:1996-07-01 00:00:00

  • The effect of cerium valence states at cerium oxide nanoparticle surfaces on cell proliferation.

    abstract::Understanding and controlling cell proliferation on biomaterial surfaces is critical for scaffold/artificial-niche design in tissue engineering. The mechanism by which underlying integrin ligates with functionalized biomaterials to induce cell proliferation is still not completely understood. In this study, poly-l-lac...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2014.01.074

    authors: Naganuma T,Traversa E

    更新日期:2014-05-01 00:00:00

  • Electron spin resonance in silicon substituted apatite and tricalcium phosphate.

    abstract::Impurity centers associated with silicon have been observed in the phase mixture of silicon substituted apatite (Si-Ap) and silicon stabilized tricalcium phosphate (Si-TCP) using electron spin resonance (ESR). Two unique centers occur upon addition of SiO2 to the calcium phosphate system: an orthorhombic center with g...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2004.10.013

    authors: Pietak AM,Reid JW,Sayer M

    更新日期:2005-06-01 00:00:00

  • Directing phenotype of vascular smooth muscle cells using electrically stimulated conducting polymer.

    abstract::Vascular smooth muscle cells (VSMCs) isolated from rabbit aorta and immortalised A7r5 cells were cultured on conducting polypyrrole (PPy) substrates and were subjected to a 50muA sinusoidal electrical stimulation at 0.05, 5 and 500 Hz. These substrates were doped with hyaluronic acid and coated with collagen IV follow...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/j.biomaterials.2008.07.052

    authors: Rowlands AS,Cooper-White JJ

    更新日期:2008-12-01 00:00:00

  • Adhesive bond strength and compliance for denture soft lining materials.

    abstract::Peel bond strength and tensile bond strength between three polyvinylsiloxane denture soft liners and a heat-cured acrylic resin denture base were measured using two adhesive systems. The soft lining materials differed only in regard of their filler content and compliance. The values of bond strength and mode of failur...

    journal_title:Biomaterials

    pub_type: 杂志文章

    doi:10.1016/s0142-9612(01)00253-8

    authors: McCabe JF,Carrick TE,Kamohara H

    更新日期:2002-03-01 00:00:00