Abstract：
:This study compared the thickness of the hybrid layer formed using Scotchbond Multi-Purpose Plus, Single Bond 2, Prime & Bond 2.1 and Xeno III on a dentin surface prepared with a diamond bur in a high speed handpiece or prepared with an Er:YAG laser used with two parameters of pulse energy (200 and 400 mJ) and two parameters of frequency (4 and 6 Hz). Flat dentin surfaces obtained from 20 human third molars were treated with the two methods and were then prepared with the dentin adhesive systems according to the manufacturers' instructions. After a layer of composite was applied, the specimens were sectioned, flattened, polished and prepared for Scanning Electronic Microscopy observation. Five different measurements of the hybrid layer thickness were obtained along the bonded surface in each specimen. The results were statistically analyzed using Analysis of Variance and Student-Newman-Keuls tests (p < or = 0.05). When analyzing the hybrid layer thickness and comparing the cavity preparation method, four groups were formed: Group I (diamond bur) > Group II (Laser 200 mJ/4 Hz) = Group III (Laser 200 mJ/6 Hz) > Group IV (Laser 400 mJ/4 Hz) > Group V (Laser 400 mJ/6 Hz). When comparing the dentin adhesive systems, there were no statistically significant differences. These results showed that the four tested dentin adhesive systems produced a 2.90 +/- 1.71 microm hybrid layer in dentin prepared with a diamond bur. This hybrid layer was regular and routinely found. In the laser groups, the dentin adhesive systems produced hybrid layers ranging from 0.41 +/- 1.00 microm to 2.06 +/- 2.49 microm, which were very irregular and not routinely found. It was also concluded that the Er:YAG laser, with the parameters used in this experiment, has a negative influence on the formation of a hybrid layer and cavity preparation methods influence formation of the hybrid layer.
journal_name
Oper Dentjournal_title
Operative dentistryauthors
de Barceleiro MO,Dias KR,Sales HX,Silva BC,Barceleiro CGdoi
10.2341/07-84subject
Has Abstractpub_date
2008-05-01 00:00:00pages
294-304issue
3eissn
0361-7734issn
1559-2863journal_volume
33pub_type
杂志文章abstract：:A fundamental issue of restorative treatment is assessing the different conditions of cases not only from tooth-to-tooth but also from the activity of each caries lesion and the size of the cavity. In addition, restorative treatment is sometimes carried out for prosthetic and cosmetic purposes and involves cutting sou...
journal_title：Operative dentistry
pub_type：
doi：
更新日期：2002-05-01 00:00:00
abstract：:The aims of this study were to investigate 1) the influence of cleansing methods after saliva contamination and 2) aging conditions (thermocycling and water storage) on zirconia shear bond strength (SBS) with a resin cement. One hundred and eighty zirconia specimens were sandblasted with 50 μm aluminum oxide particles...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/13-323-L
更新日期：2015-03-01 00:00:00
abstract：:This study evaluated the in vivo effects of bleaching agents containing 10% carbamide peroxide (Platinum/Colgate) or 7.5% hydrogen peroxide (Day White 2Z/Discus Dental) on mutans Streptococcus during dental bleaching. The products were applied on 30 volunteers who needed dental bleaching. In each volunteer, one of the...
journal_title：Operative dentistry
pub_type： 临床试验,杂志文章,随机对照试验
doi：
更新日期：2005-07-01 00:00:00
abstract：:This review compares nine published studies conducted at the Indiana University School of Dentistry. Twenty-five products in four different systems were evaluated using the Trubyte Bioform Color Ordered Shade Guide and a Chroma Meter. The dentist-prescribed overnight bleaching delta mean shade guide value (DSGV) 10 we...
journal_title：Operative dentistry
pub_type： 杂志文章,评审
doi：10.2341/08-74
更新日期：2009-03-01 00:00:00
abstract：:This research investigated the effects of wet and dry conditions of phosphoric acid etched dentin on resin bonding and determined the optimum moisture condition for resin bonding using an ethanol-based one-bottle adhesive system. Bovine dentin surfaces were etched with 35% phosphoric acid and rinsed with water. Under ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2002-11-01 00:00:00
abstract：:This study compared the amount of artificial plaque synthesized in vitro by Streptococcus sobrinus on various dental materials using radioisotopes. In particular, plaque-retaining capacities of new types of ceramics were the focus of this study. Specimens were fabricated from the following materials (one amalgam alloy...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2001-07-01 00:00:00
abstract：PURPOSE:To evaluate the effect of different strategies for post cementation on the pullout bond strength of a double-tapered glass fiber post cemented into a root canal. MATERIALS AND METHODS:The root canals of 70 single-rooted bovine teeth (16 mm-length) were prepared to 9 mm using the preparation drill of a double-t...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/08-113
更新日期：2009-07-01 00:00:00
abstract：CLINICAL RELEVANCE:When a resin nanoceramic inlay is cemented using self-adhesive cement, a universal dentin adhesive can be applied to the prepared cavity. The application of the adhesive before self-adhesive cement placement provides similar or better interfacial adaptation than without the adhesive. SUMMARY:Purpose...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/19-141-L
更新日期：2020-11-01 00:00:00
abstract：:Bleaching-induced tooth sensitivity (TS) is highly prevalent. OBJECTIVE:This study aimed to determine if the combination of opioids and nonopioids analgesics (Tylex) may provide a better analgesic effect. METHOD:A triple-blind, parallel, randomized two-center clinical trial was conducted with 105 healthy patients wh...
journal_title：Operative dentistry
pub_type： 杂志文章,多中心研究,随机对照试验
doi：10.2341/17-092-C
更新日期：2018-03-01 00:00:00
abstract：:This study was designed to compare strength, elastic modulus (stiffness), and hardness for five composite resin materials that are used for laboratory-fabricated posterior composite restorations. Ten specimens of each material were processed according to the manufacturer's instructions. Statistical analysis indicated ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1994-11-01 00:00:00
abstract：PURPOSE:To investigate the effect of different light exposure times, shades, and thicknesses on the depth of cure (DOC) of bulk fill composites. METHODS AND MATERIALS:Two bulk fill composites, Tetric EvoCeram Bulk Fill (TBF) and Sonic Fill (SF), and a conventional composite, Filtek Supreme Ultra (FSU), were evaluated....
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/16-057-L
更新日期：2017-09-01 00:00:00
abstract：:Even though accuracy and inter-examiner variation assessments of borderline restorative items have been previously reported, no attempt has been made to replicate the effect of cumulative, sequential diagnostic and treatment planning decisions. This study assesses the cumulative effect of factors indicating restorativ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2000-07-01 00:00:00
abstract：:This study evaluated the cytotoxicity of four single component dentin bonding agents: Syntac Single Component, Prime & Bond 2.1, Single Bond and One Up Bond F. The test materials were applied on dentin discs of dentin barrier models in the same way as in the clinical procedures recommended by each manufacturer. Cell v...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2003-07-01 00:00:00
abstract：OBJECTIVE:The purpose of this study was to evaluate the effects of different desensitizing agents on the prevention of root caries when applied to root surfaces. MATERIALS AND METHODS:Thirty human roots were sectioned into quarters with a 3 × 4 mm window. A desensitizer (VX, Clinpro™ XT Varnish; SP, Seal & Protect®; o...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/11-007-L
更新日期：2012-05-01 00:00:00
abstract：:This study examined the effect of different light activation modes for light-cured resin-based composites on the shear bond strength to dentin of two one-bottle adhesives with differing acidity. In this experimental study, a flat middle dentin surface was prepared on 110 extracted sound molars using a 600-grit polish ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/08-048-L
更新日期：2009-09-01 00:00:00
abstract：:This study evaluated the effect of ascorbic acid, 500 mg every eight hours, on bleaching-induced tooth sensitivity. A triple-blind, parallel design, and placebo-controlled randomized clinical trial was conducted on 39 adults. The pills (placebo or ascorbic acid) were administered three times per day for 48 hours; the ...
journal_title：Operative dentistry
pub_type： 杂志文章,随机对照试验
doi：10.2341/12-483-C
更新日期：2014-03-01 00:00:00
abstract：OBJECTIVES:To evaluate the clinical behavior of one-piece complete-coverage crowns and fixed partial dentures (FPDs) on teeth with vertical preparation without finish line biologically oriented preparation technique (BOPT). METHODS AND MATERIALS:This prospective study included 52 patients requiring treatment with rest...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/17-124-C
更新日期：2018-09-01 00:00:00
abstract：:V-shaped cervical cavities prepared in monkey teeth were restored with several dentin bonding systems, and the in vivo resin-dentin interfacial structures were observed under the scanning electron microscope using an argon-ion etching technique. The hybrid layer could be clearly observed; its depth was dependent on th...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1995-09-01 00:00:00
abstract：:Of the many factors under their control, clinicians can manipulate light-exposure duration but must deal with a set intensity of light emitted from the dental curing unit. This research investigates the interdependence of exposure duration and source intensity on resin cure at various depths within a simulated light-c...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1994-01-01 00:00:00
abstract：:The nature of the hybrid layer (HL) following chemical treatment has not been resolved. The effects of chemical treatments and polishing on HL morphology and composition were investigated using micro-Raman spectroscopy and SEM. Polished and unpolished SingleBond adhesive/dentin (a/d) interfaces from the same tooth wer...
journal_title：Operative dentistry
pub_type： 临床试验,杂志文章,随机对照试验
doi：
更新日期：2004-11-01 00:00:00
abstract：PURPOSE:To evaluate the effect of zirconia primers, air-abrasion, and tribochemical surface treatment methods on the shear bond strength between yttria-tetragonal zirconia polycrystal (Y-TZP) ceramic and self-adhesive resin cement. METHODS AND MATERIALS:Y-TZP ceramic surfaces were ground flat with 600-grit silicon car...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/13-149-L
更新日期：2015-01-01 00:00:00
abstract：PURPOSE:To investigate the influence of ferrule thickness on fracture resistance after mechanical cycling of teeth restored with different intracanal posts. METHODS AND MATERIALS:One hundred twenty bovine incisor teeth were randomized into six study groups, based on the intracanal post used (fiber post or cast post an...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/18-241-L
更新日期：2019-11-01 00:00:00
abstract：:This study evaluated the effect of different chairside polishing systems on the surface roughness and topography of monolithic zirconia. Thirty-five monolithic zirconia specimens (Lava PLUS, 3M ESPE) were fabricated and divided into five groups of seven and polished with the following: Group 1 (WZ)-Dura white stone fo...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/15-064-L
更新日期：2016-07-01 00:00:00
abstract：:The tested hypotheses of this study were that dentin enamel bonding agents (DBAs) proposed for compomers create a hybrid layer (HL) that seals the margins of Class V restorations and HL is free from voids or gaps on both enamel and dentin margins. For purposes of this study, Class V restorations (n = 70) were made in ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：2004-01-01 00:00:00
abstract：:This study compared the viscoelastic properties of restorative and flowable bulk-fill resin-based composites (RBCs) with their conventional counterparts and evaluated the impact of aqueous solutions on viscoelastic properties. The materials examined included three conventional RBCs (Filtek Z350, Tetric N Ceram, and Be...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/19-005-L
更新日期：2020-03-01 00:00:00
abstract：:This study investigated the leakage pathway of facial and lingual Class V cavities restored with different flowable resin composites bonded with one bonding agent by examining the resin/dentin interface. Forty Class V cavities were etched with 37% phosphoric acid gel; Single Bond dental adhesive was applied, then the ...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/07-22
更新日期：2008-01-01 00:00:00
abstract：:Veneers were fabricated by CEREC CAD-CAM and the platinum foil techniques for standardized preparations on 10 artificial teeth. Mesial preparation contacts were broken, but distal contacts remained intact. The veneers were cemented in a standardized manner to their teeth. The veneers and their attached cement were emb...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：
更新日期：1997-05-01 00:00:00
abstract：:This investigation examined the susceptibility to staining and translucency changes of some new tooth-colored restorative materials after immersion in different beverages. The materials studied were 3M Filtek Z350XT (ZT), 3M Filtek 350XT Flowable Restorative (ZF), Shofu Beautifil Flow Plus (BF), Shofu Beautifil II (B2...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/149027-L
更新日期：2015-03-01 00:00:00
abstract：:Hard tissue modification by means of laser irradiation is becoming popular in dentistry, since it promotes assorted responses between the tooth and the restorative material. Some studies on the bond strength of adhesive systems to Nd:YAG irradiated teeth have shown distinctive behaviors when irradiation was applied be...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/05-110
更新日期：2006-09-01 00:00:00
abstract：:Under clinical conditions, the time needed for the proper light curing of luting composites or the multi-incremental buildup of a large restoration with halogen curing units is quite extensive. Due to the development of high power curing devices, such as argon lasers and plasma arc lights and, in order to decrease cur...
journal_title：Operative dentistry
pub_type： 杂志文章
doi：10.2341/06-79
更新日期：2007-05-01 00:00:00
